This is an old revision of the document!
The purpose of packetforge-ng is to create encrypted packets that can subsequently be used for injection. You may create various types of packets such as arp requests, UDP, ICMP and custom packets. The most common use is to create ARP requests for subsequent injection.
To create an encrypted packet, you must have a PRGA (pseudo random genration algorithm) file. This is used to encrypt the packet you create. This is typically obtained from aireplay-ng chopchop or fragmentation attacks.
Usage: packetforge-ng <mode> <options>
Here is an example of how to generate an arp request packet.
First, obtain a xor file (PRGA) with either the aireplay-ng chopchop or fragmentation method.
Then use the following command:
packetforge-ng -0 -a 00:14:6C:7E:40:80 -h 00:0F:B5:AB:CB:9D -k 192.168.1.100 -l 192.168.1.1 -y fragment-0124-161129.xor -w arp-request
Assuming you are experimenting with your own access point, arp request packet generated above can be decrypted with your own key. So to see that packet we just created can be decrypted:
Enter “airdecap-ng -w <access point encryption key> arp-request”
The results look like this:
Total number of packets read 1 Total number of WEP data packets 1 Total number of WPA data packets 0 Number of plaintext data packets 0 Number of decrypted WEP packets 1 Number of decrypted WPA packets 0
To view the packet that was just decrypted, enter “tcpdump -n -vvv -e -s0 -r arp-request-dec”
The results look like this:
reading from file arp-request-dec, link-type EN10MB (Ethernet) 18:09:27.743303 00:0f:b5:ab:cb:9d > Broadcast, ethertype ARP (0x0806), length 42: arp who-has 192.168.1.100 tell 192.168.1.1
Which is exactly what we expected. Now you can inject this arp request packet as follows “aireplay-ng -2 -r arp-request ath0”.
The program will respond as follows:
Size: 68, FromDS: 0, ToDS: 1 (WEP) BSSID = 00:14:6C:7E:40:80 Dest. MAC = FF:FF:FF:FF:FF:FF Source MAC = 00:0F:B5:AB:CB:9D 0x0000: 0841 0201 0014 6c7e 4080 000f b5ab cb9d .A....l~@....... 0x0010: ffff ffff ffff 8001 6c48 0000 0999 881a ........lH...... 0x0020: 49fc 21ff 781a dc42 2f96 8fcc 9430 144d I.!.x..B/....0.M 0x0030: 3ab2 cff5 d4d1 6743 8056 24ec 9192 c1e1 :.....gC.V$..... 0x0040: d64f b709 .O.. Use this packet ? y Saving chosen packet in replay_src-0124-163529.cap You should also start airodump-ng to capture replies. End of file.
By entering “y” above, the packet you created with packetforge-ng is then injected.
This option allows you to generate LLC null packets. These are the smallest possible packets and contain no data. The switch “-s” is used to manually set the size of the packet. This a simple way to generate small packets for injection.
Remember that the size value (-s) defines the absolute size of an unencrypted packet, so you need to add 8 bytes to get its final length after encrypting it (4 bytes for iv+idx and 4 bytes for icv). This value also includes the 802.11 header with a length of 24bytes.
The command is:
packetforge-ng --null -s 42 -a BSSID -h SMAC -w short-packet.cap -y fragment.xor
If you want to generate a customer packet, first create a packet with the tool of your choice. This could a specialized tool, a hex editor or even from a previous capture. Then save it as a pcap file. Following this, run the command:
packetforge-ng -9 -r input.cap -y keystream.xor -w output.cap
When it runs, packetforge-ng will ask you which packet to use and then output the file.
Most access points really don't care what IPs are used for the arp request. So as a result you can use 255.255.255.255 for source and destination IPs.
So the packetforge-ng command becomes:
packetforge-ng -0 -a 00:14:6C:7E:40:80 -h 00:0F:B5:AB:CB:9D -k 255.255.255.255 -l 255.255.255.255 -y fragment-0124-161129.xor -w arp-request
A common mistake people make is to include either or both -j and -o flags and create invalid packets. These flags adjust the FromDS and ToDS flages in the packet generated. Unless you are doing something special and really know what you are doing, don't use them. In general, they are not needed.
This is commonly caused by using the number one (-1) instead of dash lowercase L (-l) in the command.
packetforge-ng -0 -a 00:14:6C:7E:40:80 -h 00:09:5B:EC:EE:F2 -k 255.255.255.255 -1 255.255.255.255 -y 00:14:6C:7E:40:80-03-00-14-6C-7E-40-80.xor -w arp-request
Mode already specified. "packetforge-ng --help" for help.
This because -1 was used instead of the correct -l. So simply use “-l”.