ipw2200_generic
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |||
| ipw2200_generic [2009/05/04 00:12] – Update links to forum mister_x | ipw2200_generic [2009/09/26 14:27] (current) – Fixed typos darkaudax | ||
|---|---|---|---|
| Line 6: | Line 6: | ||
| - screen usage example | - screen usage example | ||
| - Different attacks | - Different attacks | ||
| - | - More detailed | + | - More detailed |
| - | - upgrade | + | - upgrade |
| ===== Introduction ===== | ===== Introduction ===== | ||
| Line 14: | Line 14: | ||
| When I started using the aircrack-ng tools I did not have the | When I started using the aircrack-ng tools I did not have the | ||
| - | [[Compatibility_Drivers|best hardware]] for it. I only had an ibm thinkpad t42 that comes with an intel 2200BG card. | + | [[Compatibility_Drivers|best hardware]] for it. I only had an IBM Thinkpad T42 that comes with an Intel 2200BG card. |
| Most of the wep attacks require to inject some packets in the network in order to speed up the process of gathering IVs. In order to do that, the device | Most of the wep attacks require to inject some packets in the network in order to speed up the process of gathering IVs. In order to do that, the device | ||
| driver that we use for controlling our card has to support injection. This [[newbie_guide|tutorial]] explains you how to compile and install modules in your | driver that we use for controlling our card has to support injection. This [[newbie_guide|tutorial]] explains you how to compile and install modules in your | ||
| Line 26: | Line 26: | ||
| *4 - Configure the wireless parameters using iwconfig. | *4 - Configure the wireless parameters using iwconfig. | ||
| *5 - Collect data with airodump-ng | *5 - Collect data with airodump-ng | ||
| - | *5 - Launch the chopchop attack | + | *5 - Launch the [[korek_chopchop|chopchop]] attack |
| - | *6 - Create the arp request packet | + | *6 - Create the ARP request packet |
| - | *7 - Send the arp request over and over | + | *7 - Send the ARP request over and over |
| *8 - Wait to gather enough IVs | *8 - Wait to gather enough IVs | ||
| - | *9 - Crack the wep key using aircrack-ng | + | *9 - Crack the WEP key using aircrack-ng |
| Keep in mind that we are going to be running different commands and we will need to check switch between them. Most | Keep in mind that we are going to be running different commands and we will need to check switch between them. Most | ||
| Line 54: | Line 54: | ||
| | | ||
| - | That command will list all the pci devices connected to the pci bus. You should see something similar to this when you run it on your machine. | + | That command will list all the PCI devices connected to the pci bus. You should see something similar to this when you run it on your machine. |
| Note I removed most of the output. | Note I removed most of the output. | ||
| Line 68: | Line 68: | ||
| That's the method I would recommend. But, if you are using the latest version of airodump-ng (we'll use it in the next section) you can | That's the method I would recommend. But, if you are using the latest version of airodump-ng (we'll use it in the next section) you can | ||
| - | tell the program to creat the rtap0 device for you: | + | tell the program to create |
| # airodump-ng -c X rtap0 | # airodump-ng -c X rtap0 | ||
| Line 88: | Line 88: | ||
| ===== Change the MAC address of our card ===== | ===== Change the MAC address of our card ===== | ||
| - | This step is optional but it will give us some anonimyty. On a new window: | + | This step is optional but it will give us some anonymity. On a new window: |
| # ifconfig eth1 up hw ether 00: | # ifconfig eth1 up hw ether 00: | ||
| Line 127: | Line 127: | ||
| vulnerable to the chopchop attack. I also received an error stating the checksum didn't match. I just re-ran aireplay and it was fine. | vulnerable to the chopchop attack. I also received an error stating the checksum didn't match. I just re-ran aireplay and it was fine. | ||
| - | If the attack fails, try to rerun the command again ommiting | + | If the attack fails, try to rerun the command again omitting |
| ===== Create the arp request packet ===== | ===== Create the arp request packet ===== | ||
| - | Now we will create an arp-request packet using the aquired | + | Now we will create an arp-request packet using the acquired |
| If you use valid destination IPs then you will be running an [[arp_amplification|amplification attack]]. This can be run in the same window | If you use valid destination IPs then you will be running an [[arp_amplification|amplification attack]]. This can be run in the same window | ||
| we run the chopchop attack: | we run the chopchop attack: | ||
ipw2200_generic.1241388746.txt.gz · Last modified: by mister_x