ipw2200
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| ipw2200 [2008/03/23 14:40] – added 2.6.24 kernel support darkaudax | ipw2200 [2017/01/09 21:28] (current) – Mark page as deprecated. mister_x | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== | + | ====== |
| - | + | ||
| - | At this point in time, this page is far from complete. | + | |
| + | **IMPORTANT NOTE**: This page is deprecated, updated documentation can be found [[install_drivers|here]] | ||
| + | ====== ipw2200 ====== | ||
| + | At this point in time, this page is far from complete. | ||
| ====== ipw2200-1.2.1 how to ====== | ====== ipw2200-1.2.1 how to ====== | ||
| Line 55: | Line 56: | ||
| ====== 2.6.24 kernel support ====== | ====== 2.6.24 kernel support ====== | ||
| - | See this [[http:// | + | See this [[http:// |
| For the code see: | For the code see: | ||
| * http:// | * http:// | ||
| - | |||
| ====== Troubleshooting Tips ====== | ====== Troubleshooting Tips ====== | ||
| - | |||
| ===== Airodump-ng will not channel hop ===== | ===== Airodump-ng will not channel hop ===== | ||
| If you want to channel hop, use the ethX interface where X is the interface that got created while loading the driver. | If you want to channel hop, use the ethX interface where X is the interface that got created while loading the driver. | ||
| - | + | ===== How do I get the rtapX interface ===== | |
| - | + | ||
| - | ===== How do I get the rtapX interface | + | |
| You get it by specifying rtap_iface=1 while loading the driver or by setting the appropriate value in /sys. | You get it by specifying rtap_iface=1 while loading the driver or by setting the appropriate value in /sys. | ||
| The rtapX interface allows packet capture while you are in managed mode. | The rtapX interface allows packet capture while you are in managed mode. | ||
| + | |||
| + | ===== "rtap0 is on channel 0, but the AP uses channel X" message ===== | ||
| + | |||
| + | Try adding the channel settings to the modprobe: | ||
| + | |||
| + | | ||
| + | |||
| + | Where X is the AP channel. | ||
| + | |||
| + | ===== Deauthentication does not work ===== | ||
| + | |||
| + | The ipw2200 driver does not support the transmission of management frames such as deauthentication. | ||
| ====== Useful links ====== | ====== Useful links ====== | ||
| + | * [[http:// | ||
| * [[ipw2200_generic|Tutorial: | * [[ipw2200_generic|Tutorial: | ||
| * [[http:// | * [[http:// | ||
| - | * [[http://tinyshell.be/ | + | * [[http://forum.aircrack-ng.org/ |
| - | * [[http://tinyshell.be/ | + | * [[http://forum.aircrack-ng.org/ |
| - | * [[http://tinyshell.be/ | + | * [[http://forum.aircrack-ng.org/ |
| - | * [[http://tinyshell.be/ | + | * [[http://forum.aircrack-ng.org/ |
ipw2200.1206279643.txt.gz · Last modified: by darkaudax
